Looking for a way to jazz up your wall artwork? Test producing your have Do-it-yourself acrylic frames for individualized 3D artwork. This write-up will wander you by means of just how I manufactured these in my residence.
If you are seeking for a personalized way to body your pictures or artwork to make it stand out from the wall, these Do it yourself acrylic frames are the ideal matter.
I landed on these frames simply because I essential a minor one thing to increase a minor more pizzazz to my lavatory wall. 
We resolved to incorporate my partner&rsquos enjoy of golf into the combine by printing photos he took of PGA golfing courses he&rsquos performed in black and white.
I really like when artwork is a dialogue piece, so this was the fantastic addition to the lavatory wall.
To make it really stand out, I manufactured these Diy acrylic frames for every of the pictures.
Here are the methods I took&hellip 
Desk OF CONTENTS
- 1. Gather your supplies.
- 2. Tape every facet of each and every corner.
- 3. Mark where by you want to drill your holes.
- 4. Drill your holes.
- five. Use click for more to secure your photos to the body.
- six. Mark the entire on the wall where by you approach to hold it.
- seven. Use your punch device to mark the entire on the wall.
- 8. Drill your holes in the wall.
- 9. Screw the standoffs into the wall.
- ten. Connect your body to the standoffs.
- 11. Revel in the finished merchandise!
Disclaimer: This post does include affiliate links for your ease. This is at NO further expense to you but earns me a small fee. To read extra, check out our disclosure policy.
one. Obtain YOUR Components.
1st factors very first, assemble all your products. All resources for everything I used are connected under. I also included a listing with links of what we applied to hang the frames, way too. 
FOR Building THE Diy ACRYLIC FRAMES:
- Plexiglass/Acrylic Sheets
- Standoffs
- Glue Dots
- Piece of Lined Paper
- Drill 
- Drill Bits (one for the measurement of the opening of your standoffs and a person for the screw for the wall)
- Painter&rsquos Tape
- Ruler
- Marking Software (I used a Sharpie)
FOR HANGING THE Diy ACRYLIC FRAMES:
- Pencil
- Handheld Stage
- Punch
- Screwdriver
two. TAPE Every Facet OF Every single CORNER.
Plexiglass/acrylic is really sensitive.
Because of this, you have to be very very careful when you are drilling the holes.
Positioning a piece of painter&rsquos tape on either facet the place you system to drill your hole will help preserve the acrylic sheet from breaking or cracking when you drill.
I also retained the protecting include on every side of the piece, also.
3. MARK Where YOU WANT TO DRILL YOUR HOLES.
The moment you have placed the painter&rsquos tape on all four sides (or having said that a lot of sites you strategy to drill a gap), you can spot a mark of where you want to drill your gap.
I drilled my holes one&Primary in from each and every edge as you can see from the photograph over.
four. DRILL YOUR HOLES.
Ahead of in fact drilling, double and triple check out that your marks are level both equally horizontally and vertically.
You&rsquoll want to have these degree for when you hold them. 
The drill bit you pick need to be big more than enough to permit the standoff to fit inside the hole.
I would do a check operate on a piece of scrap content to make absolutely sure it is large more than enough. 
At the time you are sure that the marking are stage and the little bit is major enough, you want to start out drilling.
Here is a superior online video to observe if you would like a demonstration on how to drill by acrylic.
You want to use about half electricity when you are drilling.
Sluggish and continual. If you go to rapidly, the acrylic will crack, so just take your time.
As you drill you should see spirals of the acrylic slowly getting taken off. 
Repeat the drilling for each individual hole you have to have.
5. USE YOUR GLUE DOTS TO Protected YOUR Photographs TO THE Body.
The moment your holes are created, you can insert your image to the piece of acrylic/body.
The key here is to again, make absolutely sure your photograph is stage in advance of you wholly protected it to the frame.
The glue dots are incredibly sticky and don&rsquot permit for a good deal of wiggle place, so it may perhaps be a superior concept to line up a piece of lined paper powering the body to enable you line the edges of your photo.
What ever trick works for you to make guaranteed the picture will get glued to the frame stage will do. 
six. MARK THE Full ON THE WALL Exactly where YOU Prepare TO Hold IT.
As you start to cling, mark your holes on the wall, but make absolutely sure your frame is level.
If you measured appropriately in the stage ahead of drilling, the holes on your body really should previously be stage.
If you are hanging more than one body like I did, make guaranteed each and every frame is level in your grid, much too. 
seven. USE YOUR PUNCH Tool TO MARK THE Whole ON THE WALL.
I adore this tool so considerably since it will get your hole commenced and will allow your drill to continue to be in location when you get started drilling.
If you don&rsquot have one, I highly endorse it!
eight. DRILL YOUR HOLES IN THE WALL.
Be confident to use a little bit that matches the screws that arrived along with your standoffs.
This will most probable be a more compact bit than the a person you utilised on the frames.
I also utilized a stud finder to see if I wanted drywall anchors, but since these frames are not that weighty, you could most likely do without the need of them.
nine. SCREW THE STANDOFFS INTO THE WALL.
Once you order your standoffs, you&rsquoll see how they operate.
In order for the image to &ldquostand off&rdquo the wall, you have to secure the standoff with the delivered screw before attaching the photo to the standoffs.
As you can see from the image, earning sure all the things is stage and calculated properly is super crucial. 
ten. Connect YOUR Frame TO THE STANDOFFS.
When you&rsquove attached the standoffs, it&rsquos time to connect the images!
Line up the standoffs with your drilled holes and secure the standoffs.
If all goes perfectly, almost everything will line up properly and be ready to go!
If you are like my father and I, you&rsquoll appear across at least just one that doesn&rsquot line up completely.
For this, we cheated a very little little bit and secured the standoff to the frame and used a glue dot to safe it to the wall, so it didn&rsquot shift.
We only experienced to do this for two corners of two frames, but don&rsquot fret if you mess up 1&hellip We&rsquove been there! 
11. REVEL IN THE Finished Solution!
Now it&rsquos time to love your do the job!
We did a grid of 9 total pictures which was a major undertaking with all the measuring, but I&rsquom in really like with how it turned out.
Let me know in the remarks what you imagine of the concluded item!